Nu-EcoSafe Strip Architectural - Fisher Group

Nu-EcoSafe Strip Architectural

Nu EcoSafe Rust converts existing surface rust into a stable compound, reading for priming and coating

$66.45$146.11

Clear
  • Next day delivery
  • Top quality products
  • Money back guarantee

Water-Based Non-toxic Paint Remover Suitable for Architectural Coatings

Nu-EcoSafe Strip Architectural is a brushable water-based paint remover that is biodegradable, non-toxic, user-friendly and environmentally safe. It is extremely effective in removing architectural coatings.

Nu-EcoSafe Strip Architectural has proven it will effectively lift:

  • Thin-film urethanes
  • Thin-film latex and lacquers
  • Alkyd paints and varnish
  • Elastomeric coatings

Will remove these coating from all types of substrates including:

  • Vinyl floor coverings
  • Wood
  • Aluminium
  • Metal alloys
  • Concrete
  • Masonry

Nu-EcoSafe Strip Architectural is effective at the following projects:

  • Interiors of buildings and homes
  • General paint removal
  • D.I.Y markets for paint removal
  • Safe on a vinyl composite tile (VCT)
  • Hospitals
  • Institutional flooring
  • Coating and sealant stripping.

Nu-EcoSafe Strip Architectural has the following qualities:

  • Water-based
  • Fully biodegradable
  • Non-flammable
  • Contains no TAPs or HAPs (Toxic/Hazardous Air Pollutants)
  • Non-carcinogenic
  • Easy clean up with running water
  • Low VOCs
  • Non-ozone-depleting
  • Not regulated by authorities for transportation/storage
  • Not regulated by authorities for worker health and safety
  • Low odour
  • Will not burn skin

Additional Benefits that contribute to Cost-effectiveness:

  • Requires much less chemical to achieve desired results
  • Reduces man-hours and effort required to complete a project
  • Reduces the cost of waste disposal
  • Reduces downtime since other work at the site can continue while stripper does its job
  • Lowers insurance costs for storage hazards.

 

Suitable Surfaces

Properties

Biodegradable
Low VOC
Non-flammable
Water Based
Water Clean-up
[/col]

 

DOWNLOAD CARE & MAINTENANCE BROCHURE

Download Technical Data Sheet

Download Safety Data Sheet

Weight4 kg
Appearance

White Liquid

pH

11.14

VOC Levels

75.5 g/L

Coverage Rate

1 – 2.2 m2/L m2/L

Size

4L, 10L

Application Guide

Equipment & Tools
This product is engineered for spray or brush application.

Airless sprayers are recommended. Use only airless equipment with chemical resistant packing, that has an output of 2 L/min and can produce a pressure of 2500 psi. A typical medium-size airless sprayer is capable of spraying this product. Equip the sprayer with a tip size of 0.019 inches or larger. (Example: a 519 or 425 tip).

Other equipment: brushes, rollers, scraper, masking tape, plastic (polyethylene) sheet, pressure washer, electric drill with mixer, empty pails for clean-up, running water, rags. Roller application should be used only for horizontal surfaces.

Preparation
Cover/protect areas where stripping is not desired, including adjoining surfaces where overspray may travel. Polyethene sheets make a very effective barrier. If using masking tape, apply two layers of tape and remove the top layer immediately after application as the remover may soak through the tape, damaging paint under it. Plants should be covered or washed thoroughly with water before and during application.

Never shake Nu-EcoSafe-Strip Architectural Paint Stripper. Shaking will cause the product to separate. Using a drill mixer, mix product until it is uniform in colour and is creamy in consistency, (About 1 minute per 4 litres).

Test Patch
Conduct a small test patch in an inconspicuous area to ensure product performance. This will indicate the time required for project completion, the suitability of the product for paint and substrate, and most effective removal method.

Application Procedure
Apply a thick, even layer of stripper onto the coating being removed. An airless sprayer is the most effective means for application. Always start the sprayer pump at the lowest pressure setting and slowly build up the pressure until an adequate fan pattern has been generated. High pressure and narrow tip sizes will break the stripper’s emulsion and will destroy its effectiveness.

The stripper must be applied 1.5 to 2 times the thickness of the coating being removed, i.e 20 mils of coating require 30-40 mils of stripper to be removed effectively. When trying to build up films thicker than 30 mils (600 microns), or when trying to apply the stripper on a glossy or greasy vertical surface, it is advisable to build the stripper film in two separate applications.

First apply a light coat of approximately 15 mils (300 microns), thick enough to hide the surface colour of coating and allow it to dwell for 5 to 30 minutes and then build the rest of the stripper film thickness in a second application.

Once applied, leave the stripper alone, as agitation slows down penetration. If using a brush, make sure the underlying surface is completely covered with Nu EcoSafe Strip Architectural Paint Stripper.

First Applications
For removal of thin-film urethanes, Nu EcoSafe Strip can be applied with a mop, roller or a squeegee. Dwell time is between 30 to 60 minutes. Janitorial floor machines can be used for agitation and removal of coating and stripper residue. A generous water rinse will complete the removal process.

Re-Application
If poor adhesion exists between paint layers, the remover may lift the coating between weak layers. If this happens, remove the lifted layers with a dry scraper and re-apply Nu EcoSafe Strip. Do not rinse with water between applications. While the removal process is taking place, do not allow the stripper to dry on the surface. If it starts to dry, reapply the stripper.

Dwell Time
The time required for penetration varies according to the type of paint, the thickness of the paint, and the temperature. Most paint systems require between 2 to 36 hours. Nu EcoSafe Strip Architectural Paint Stripper can be left overnight, but do not allow it to dry out. If you are trying to remove wax, the process should not take longer than 30 minutes to 1 hour.

Coverage
Coverage is approximately 1 to 2.2 sq.m./L depending on substrate and coating to be removed.

Optimum Temperature
Above 13°C if working in cooler temperatures expect longer dwell time. Keep from freezing.

Removal & Clean Up
Removal of residue can be completed by a scraper, squeegee, mop, wet/dry vacuum system or by a high-pressure washer. Be careful if using a high-pressure washer on porous surfaces as it may damage the surface. A floor cleaning machine can also be used by going back and forth over the floor with the buffer function and then using the vacuum function to suck up the residue. For wood projects, remove lifted paint with a scraper first, then lightly rub with an abrasive nylon open web hand pad (i.e. Scotch- Brite™) to remove remaining paint from the wood grain. Collect lifted paint and place it in plastic containers, Add Nu Ecosafe Strip Ecozorb to absorb the remaining liquids and dispose of in accordance with local government regulations.